IQ8MCP electronic module w/o isolator, with relay

804906 | IQ8MCP electronic module w/o isolator, with relay

Addressable electronic module with floating contacts of a changeover relay NC/C (break) or NO/C (make), suitable for use in the esserbus and powered loop with alarm latch and alarm indicator. Without BUS connection, the detector operates as conventional MCP.

Without built-in loop isolator and optional connection for conventional MCP.The relay output is activated with the triggering of this detector. The relay output can be programmed in the System 8000 and IQ8Control FACP customer data as a control group with freely programmable trigger functions.

Part-No.:
804906
Approval:
VdS

Features

  • Slimline design
  • Low power consumption
  • Plug-in connection clamps
  • Optional terminal clamps
  • 2 x cable entries on top, at the bottom and on the rear panel
  • Fixing on standard flush mounted installation box
  • Test function via manual call point service key
  • Detectors that are not ready for operation can be marked with the "Out of order" label by reversing the enclosed operating front foil

Technical Data

Common technical data: 
Leistungserklärung 
Rated voltage 
V AC
Rated frequency 
Rated current 
Output current 
Battery capacity 
Operating voltage 
8 ... 42 V DC
 
Operating voltage 
V DC
Operating voltage 
Quiescent current 
Lichtquelle 
Leuchtfarbe 
 
Quiescent current @ 9 V DC 
μA
Quiescent current @ 12 V DC 
Quiescent current @ 19 V DC 
45 μA
Quiescent current @ 24 V DC 
Quiescent current @ FACP battery 
Quiescent current @ FACP battery 
Quiescent current 
μA
Current consumption 
Current consumption 
Current consumption @ 12 V DC 
Current consumption @ 24 V DC 
Starting current 
mA
Current consumption in the case of failure 
mA
Current consumption testmode 
mA
Alarm current 
Alarm current 
Alarm current @ 9 V DC 
mA
Alarm current @ 12 V DC 
Alarm current @ 24 V DC 
mA
Alarm current @ 24 V DC 
Alarm current w/o communication curtain 
18 mA
Power consumption 
Current consumption for ext. devices 
A
Testing capacity 
Battery charging 
Heat detector response threshold 
Load factor 
Contact load relay 
30 V DC / 1 A
Contact load 
Sound level 
dB
Sound level @ 12 V DC 
Sound level @ 24 V DC 
Sound level 
No. of detector/zone 
10 detectors per zone, 127 detectors/loop (according to VdS)
Circuit 
Display 
Operation indicator 
LED, green
Alarm display 
LED, red
Fault display 
Frequency of flash 
Lighting energy 
Flash color 
Luminous intensity 
 
 
Signal flashing lamp 
Range 
Connection terminal 
max. 2.5 mm² (AWG 26-14)
CO pre-alarm 
ppm
CO alarm 
ppm
Area to be monitored 
Height to be monitored 
Air velocity 
Sensitivity 
Application temperature 
-20 °C ... 70 °C
Ambient temperature 
Storage temperature 
-30 °C ... 75 °C
Air humidity 
< 95 %
Air humidity 
Type of protection 
IP 44 (in housing), IP 55 (with accessory)
 
Protection class 
Ex. protection 
Category 
Housing 
PC ASA plastic
Material 
 
Installation 
Signal Range 
Mounting height wall 
Room width 
Category ceiling 
Mounting height ceiling 
Room diameter 
Color 
 
Weight 
approx. 236 g (in housing)
Weight 
Optisches_Signalbild 
Lebensdauer_optisch 
Drehfrequenz 
Abmessungen 
Content 
Cable length 
m
Maximum sensor length 
m
Detector specification 
EN 54-11, type B
DIBt approval 
Specification 
 
Cable diameter 
mm
Cable entry 
Maximum tube length 
Dimensions 
W: 133 mm H: 133 mm D: 36 mm
 
Length 
Declaration of Performance 
DoP-20488130701
Konformität 

Additional information

For a large MCP, the electronic module and the MCP housing must be ordered separately to have a complete MCP.

Product Data Sheet

Version: 2024-12

Language:
English
Doc extension:
pdf